MUTOH ValueJet VJ-1204 Operation Manual Download Page 79

Page: 79 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-17

4.4

Operating from the operation panel

This section explains various functions that can be operated from the operation panel.

TIP

• For names and functions of each key, refer to "2.2.3 Operation panel".

4.4.1

Feeding media

You can feed roll media at a position that you want.

Follow the procedure below to feed media.

1. Confirm that the operation panel is Normal.

2. Confirm that the media loading lever is returned to the front.

3. Press the [Forward

↓

] key or the [Backward

↑

] key on the operation panel.

•

Media is fed forward or backward.

4. Release the [Backward

↑

] key or [Forward

↓

] key on the operation panel after feeding media to the

desired position.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands