MUTOH ValueJet VJ-1204 Operation Manual Download Page 16 | Manualshive

Page: 16 / 186

background image

1 Safety instructions

VJ-1204 OPERATION MANUAL

1-6

1.3

Warning labels

This section explains the handling of warning label, pasting location and types.
Warning labels are attached to parts of the printer that need special caution. Understand the locations
and the descriptions of the danger associated with each label before operating the printer.

1.3.1

Handling the warning labels

When handling the warning labels, be careful about the following points.

NOTE

• Check whether all the warning labels can be read. If the letters or illustrations on the label are not

clear, remove the dirt from the label.

• Use cloth, water and neutral detergent for removing dirt from the warning label. Avoid either

organic solvents or gasoline.

• It is necessary to replace the labels if they are damaged, lost or illegible.

If the warning labels have to be replaced, contact your local MUTOH dealer.

1.3.2

Location and type of warning labels

Pasting locations of the warning labels are shown in the following figure.

No.

Types of warning labels

1

1

«
...
14
15
16
17
18
...
»

Summary of Contents for ValueJet VJ-1204



























































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1204

Brand: Xerox Pages: 73

Brand: Xerox Pages: 2

Brand: Panasonic Pages: 155

Brand: Panasonic Pages: 160

Brand: Panasonic Pages: 102

Brand: 3Doodler Pages: 8

DiMAGE Scan Elite 5400 II

Brand: Konica Minolta Pages: 38

WorkCentre BookMark 40

Brand: Xerox Pages: 12

Brand: Olivetti Pages: 74

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: Tally Dascom Pages: 2

Brand: U-Line Pages: 18

Brand: Konica Minolta Pages: 8

Brand: Evolis Pages: 63

Brand: Lexmark Pages: 8

SEH InterCon PS54a-G

Brand: SEH Pages: 24

Brand: VORON Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands