MUTOH ValueJet VJ-1204 Operation Manual Download Page 67

Page: 67 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-5

4.2.4

Printing area

The printable area of this printer is as follows.

4.2.5

Head height adjustment

Printing with high printing rate or using strongly-curved media can cause print heads to rub.
Changing the head height may allow you to avoid head rub.
Follow the procedure below to change the head height.

4.2.5.1

When raising the print head

NOTE

• If the head height adjustment lever is raised, high print quality is not guaranteed.

• Do not open the front cover or change the head height during printing. If the head height is changed,

the alignment will be changed and high print quality will not be guaranteed.

Printable Area

a=3mm
b=3mm
c=3mm
d=3mm

Media f

eeding direction

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands