MUTOH ValueJet VJ-1204 Operation Manual Download Page 82

Page: 82 / 186

4 Handling the printer

VJ-1204 OPERATION MANUAL

4-20

4.4.4

Changing and confirming settings while printing

While the printer is operating, you can change or confirm settings for the Panel setup menu.

4.4.4.1

Procedure for changing and confirming settings while printing

Follow the procedure below to change or confirm settings for the Panel setup menu.

1. Confirm that the printer is in one of the following conditions.

•

Receiving

•

Converting

•

Printing

•

Warming up

2. Press the [Menu] key on the operation panel.

•

"Menu 1: Print Start" is displayed on the operation panel.

3. Press the [+] key or [–] key to change or confirm settings.

NOTE

• For the setting items whose settings can be changed or confirmed, refer to "4.4.4.2 Settings that

can be changed or confirmed while printing".

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands