MUTOH ValueJet VJ-1204 Operation Manual Download Page 53

Page: 53 / 186

VJ-1204 OPERATION MANUAL

3 Before using

3-27

3.6

Adjust print

It is used for optimizing the quality of image prints (Alignment).

Alignment must be set every printing mode.

After selected the printing mode that you want to use, follow the procedure below to perform alignment.

NOTE

• This printer was adjusted at factory shipment so that it obtains the optimum print quality.

Adjust the quality if the print quality changes after the installation environment or the media is changed.

1. Turn ON the printer and load the roll media.

3.4.2 Setting roll media

2. Confirm that the printer functions normally.

3. Display the Printing mode menu on the operation panel.

a. Press the [Menu] key on the operation panel.

•

"Menu 1: Setup>" is displayed on the operation panel.

•

The operation panel shifts to the Setup menu display.

b. Press the [>] key on the operation panel.

•

"Set1: MediaType" is displayed on the operation panel.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands