MUTOH ValueJet VJ-1204 Operation Manual Download Page 31

Page: 31 / 186

VJ-1204 OPERATION MANUAL

3 Before using

3-5

3.2

Turning the power ON/OFF

This section explains how to turn the printer ON/OFF.

3.2.1

Turning the power ON

Follow the procedure below to turn the power ON.

1. Press the [Power] key on the operation panel to turn ON the printer.

•

The Power lamp on the operation panel lights up in green.

•

The printer starts initial operation.

•

When the initial operation is complete, the printer enters Normal.

NOTE

• If there is a problem during initial operation, the printer displays a message on the operation

panel and may stop operating.
If operation stops, refer to "7 Troubleshooting" and deal with the problem.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands