MUTOH ValueJet VJ-1204 Operation Manual Download Page 75

Page: 75 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-13

9. Set up Micro Adjustment Change.

a. Press the [+] key or [–] key to select "PF5:Micro Change".

b. Press the [Enter] key on the operation panel.

•

"Micro: 0pulse" is displayed on the operation panel.

c. Press the [+] key or [–] key and enter the micro adjustment value according to the printing result

in step 7.

d. Press the [Enter] key on the operation panel.

•

The micro adjustment value is saved.

•

"PF5:Micro Change" is displayed on the operation panel.

10. Press the [Cancel] key on the operation panel several times.

•

The operation panel returns to Normal.

•

The adjustment of media feed compensation value is complete.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands