MUTOH ValueJet VJ-1204 Operation Manual Download Page 125

Page: 125 / 186

VJ-1204 OPERATION MANUAL

6 Maintenance

6-3

(2) Type

Our genuine ink cartridges that are compatible with the printer are as follows.

NOTE

• Use genuine ink cartridges for replacement.

This printer is designed to use genuine ink cartridges. If you use an ink cartridge that is not a product
of the original manufacturer,

• Printing might become blurred, or the end of the ink in the cartridge might not be detected

correctly.

• Any problems caused by using an ink cartridge other than those recommended above will not be

covered by the warranty, and repair expenses will be paid by the customer.

(3) Replacing steps

Follow the procedure below to replace the ink cartridges.

CAUTION

• When handling ink cartridges, pay attention so that ink does not get into your eyes

or stick to your skin. If ink gets into your eyes or sticks to your skin, immediately
wash it off with water.
Failing to do so might cause irritation or light inflammation of eyes. In case of any
abnormality, consult a physician immediately.

• Do not disassemble ink cartridges. If disassembled, there is a possibility that ink

might come into contact with eyes or skin.

Description

Model No.

Ink cartridge K (Black: 220 ml)

VJ-MSINK3-BK220

Ink cartridge C (Cyan: 220ml)

VJ-MSINK3-CY220

Ink cartridge M (Magenta: 220 ml)

VJ-MSINK3-MA220

Ink cartridge Y (Yellow: 220 ml)

VJ-MSINK3-YE220

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands