MUTOH ValueJet VJ-1204 Operation Manual Download Page 25

Page: 25 / 186

VJ-1204 OPERATION MANUAL

2 Product overview

2-7

2.3

Printer status

This chapter explains printer status.

2.3.1

Normal

Printing is possible when media is loaded.
The various functions for printing can be performed on the operation panel.

2.3.2

Setup menu display

Various settings regarding printing can be made from the operation panel.
The various functions for printing can be performed on the operation panel.
Display contents in the LCD monitor of the operation panel are as follows.

2.3.3

Changing printer status

Follow the procedure below and change plotter status.

(1) Normal

→

Setup menu display

Press the [Menu] key on the operation panel when the printer is Normal.

•

"Menu 1: Setup>" is displayed on the operation panel and the display shifts to the Setup menu.

NOTE

• For details regarding the Setup menu, refer to "4.3 Menu setups on the operation panel".

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands