MUTOH ValueJet VJ-1204 Operation Manual Download Page 94

Page: 94 / 186

5 Panel setup menu

VJ-1204 OPERATION MANUAL

5-10

5.1.1.1.4

Platen Heater menu

Sets up the Platen Heater temperature.
Set up this menu to warm up ink and improve print quality.

NOTE

• Preset temperature of Platen Heater varies depending on the media.

For preset temperature of Platen Heater, refer to the "Recommended media list".

Setup item

Setting

Description

Platen Heater

Off / <30° C> to 50° C

Sets up the Platen Heater temperature.

1.Roll media
2.Platen Heater
3.Print head

—

• [Enter] key: saves the setting and shifts to the

previous menu.

• [Cancel] key: cancels the setting and shifts to the

previous menu.

5.1.1.1 User media menu

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands