MUTOH ValueJet VJ-1204 Operation Manual Download Page 83

Page: 83 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-21

4.4.4.2

Settings that can be changed or confirmed while printing

NOTE

• The Print start menu is displayed only when the printer is warming up.

• When you change a setting during operation, be sure to select "Backup" to save the setting that you

changed.
If the printer returns to Normal without "Backup" being selected, the changed setting is not saved.

Setup item

Setting

Description

Print Start

—

• [Enter] key: If the heater temperature does not reach

the set value during warming-up, printing starts.

Temperature

Pre

Check the current Pre Heater temperature.

Platen

Check the current Platen Heater temperature.

After

Check the current After Heater temperature.

Pre Heater

Off / 30 °C to 50 °C

Change the Pre Heater temperature.

Platen Heater

Off / 30 °C to 50 °C

Change the Platen Heater temperature.

After Heater

Off / 30 °C to 50 °C

Change the After Heater temperature.

PF Adjust

–20 pulse to 0 to 20 pulse

Change the feed adjustment value.

Backup

—

• [Enter] key: Save the changed setting.

—

• [Cancel] key: The printer returns to Normal.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands