MUTOH ValueJet VJ-1204 Operation Manual Download Page 6

Page: 6 / 186

About this Manual

VJ-1204 OPERATION MANUAL

(4)

4.Manual Notation

This section explains general cautions that must be followed in order to use this printer safely.

Warning

Meaning

Used for dangerous situations where death or serious injury may be caused.

Used for dangerous situations that may cause slight or medium injury, or when all or parts of
products are damaged.

It is used for special cautions and for information that needs to be emphasized.

Indicates useful tips for operating or understanding the printer.

Indicates "prohibited" operations.

Indicates required operations.

Indicates reference pages in this manual.

WARNING

CAUTION

NOTE

TIP

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands