manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 9 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 9

Regulary & Safety Information 

Operation Instructions Rockhopper Printer

 

 

Page 

9

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

REGULATORY AND SAFETY INFORMATION 

 

EMC STATEMENT FOR CE MARKING 

 

 

Warning:

 

•

  This is a class A product.  In a domestic environment this product may 

cause radio interference in which case you may be required to take 
adequate measures. 

 
 

FCC COMPLIANCE 

 
This equipment complies with the requirements for a Class A computing device in the FCC 
rules, part 15, subpart J. 
 
Operation of this device in a residential area may interfere with television reception or 
operation of utilities. 
 
Printers generate weak radio signals and may interfere with television reception and 
utilities.  If the printer does interfere with radio or TV reception, try the following : 
 

•

  Change the direction of your radio and TV reception antenna or feeder. 

•

  Change the direction of the printer. 

•

  Move either the printer or the receiving antenna so there is more distance between 

them. 

•

  Be sure the printer and the receiving antenna are on separate power lines. 

 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments