manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 29 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 29

Installation Procedures 

Operation Instructions Rockhopper Printer

 

 

Page 

29

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

THE PARALLEL INTERFACE 

 

Caution: 

•

  When connecting the printer to your computer, make sure that both 

your printer and your computer are switched OFF. 

 

 

Note: 

•

  For optimum output, please use a cable recommended by Mutoh.  

 
The printer can use the Centronics interface (IEEE1284 compatible, Nibble, ECP).  
Connect to the printer as shown in the following diagram with an interface cable (option) 
for the connection system you will use.  Connect to the host computer with another 
interface cable. 
 
 

 

Note: 

•

  The use of an unnecessary long cable may influence your data 

transmission.  Therefore, keep your interface cable as short as 
possible.

 

•

  An Ethernet board RJ-ETH14TX (for networking) is available as an 

optional extra.

 

 

 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments