manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 65 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 65

Daily Maintenance 

Operation Instructions Rockhopper Printer

 

 

Page 

65

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

CLEANING THE HEAD CLEANING WIPER. 

When the head is cleaned and the type of ink is changed frequently, waste matter clinging 
to the cleaning wiper may cause the printing to become faint or blemished.  In such case, 
you should clean the cleaning wiper. 

Step 1:

 

Switch off the power, lower the hold lever and bring the head to the middle. 

 

Caution:

 

•

  Do not move the head with the hold lever up.  The head and media 

keeper blade may touch, causing damage and poor printing quality. 

 

Step 2:

 

Clean the cleaning wiper backwards and forwards two or three times with the cloth for 
cleaning the cleaning wiper. 

 

 

1. Head cap unit 
2. Cleaning wiper 

 

 
 

 

Caution:

 

•

  Clean without your hand coming into direct contact with the head cap 

unit, which is near the cleaning wiper.  Otherwise oil may get on the 
cleaning wiper and it will be unable to clean the head properly. 

•

  Do not lift up the cleaning wiper when you are cleaning it.  Otherwise it 

is unable to clean the head properly. 

•

  The cleaning wiper and its surroundings will be soiled with waste 

liquid.  Be careful not to dirty your hands and clothes. 

 

Step 3:

 

Return the head to its former position at the right hand end of the printer. 

 

Caution:

 

•

  The head may be damaged by drying ink, etc. if it is not returned to the 

right hand end of the printer. 

 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments