manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 19 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 19

Installation Procedures 

Operation Instructions Rockhopper Printer

 

 

Page 

19

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

UNPACKING YOUR ROCKHOPPER PRINTER 

 
The printer body and printer Take-up system are packed in two separate boxes.  

Unpack 

the printer body first.

 

 

 

 

Caution: 

•

  When unpacking the printer, check whether all parts described in the 

parts list are included in the box.  Consult your dealer if anything 
seems to be missing. 

•

  Lifting the machine out of the box should be done by four people. 

•

  Protect the printer from shocks. 

•

  Do not dismantle the unit. 

 

Procedure for unpacking the printer:

 

 

Step 1:

 

Remove the top cover cardboard and big sleeve. 
 

Step 2:

 

Take out the leg set, accessories box, extra media 
scroller, beams,… 

 

Step 3:

 

Open the printer body box. 
 

Step 4: 

Remove all plastic and cardboard pieces holding the printer body. 
 

Step 5:

 

Take out your media scroller 
 

Step 6:

 

Check whether all parts described in the parts list are included in the box.  Consult your 
dealer if anything seems to be missing. 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments