manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 39 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 39

Preparing for a job 

Operation Instructions Rockhopper Printer

 

 

Page 

39

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

 

Note: 

•

  In case the ink cassettes are installed and the display message “NO 

CARTRIDGE” still appears, this means that the ink cassettes are not 
inserted correctly.

  

Pull out the cassette(s) indicated and try to insert it 

(them) correctly. 

•

  In case of failure of initial ink replenishment, apply head cleaning a 

couple of times.  If the ink replenish does not commence after several 
head cleaning cycles, contact your dealer. 

•

  If the display shows “not original ink” please contact your ink supplier 

and make sure to get original Mutoh Rockhopper ink. 

 
 
 

B. Installing Ink Cassettes.

 

 

Step 1:

 

The power switch is located at the right side of the printer, 
below the printer body. 

Turn the switch ON and put the hold lever in the DOWN 
position. 

Step 2: 

The printer starts up its initialization routine and the printer display shows the following 
message: 
 
 
 
Y: Yellow 
M: Magenta 
C: Cyan 
K: Black 
O: Orange or Light Cyan 
G: Green or Light Magenta 
 

 

Note : 

 

•

  If the cover is open or the hold lever is up, the initialization routine will 

not start. 

 

 

Step 3: 

Insert 6 ink cassettes one by one, respecting the order shown in the illustration below. 

[Y M C K O G] No cartridge 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments