manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 31 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 31

Installation Procedures 

Operation Instructions Rockhopper Printer

 

 

Page 

31

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

INSTALLATION OF NETWORK INTERFACE BOARD 

The standard interface for the Rockhopper printer has a parallel Centronics compatible 
interface as standard equipment.  The network interface board, RJ-ETH14TX, for 
connection to EtherNet is also available as an option. 
The following procedure explains how to install the network interface board. 
 

 

Caution:

 

•

  When installing the Network interface board, make sure that the 

Rockhopper printer is switched off and the power cable is 
disconnected. 

 

To install the network card proceed as follows:

 

Step 1 : 

 

 

Loosen the two screws, which are fixed to 
the interface cover plate on the left side of 
the Board box below the printer and remove 
the plate. 

1. Interface cover plate 
2. Board box 

Step 2 : 

 

 
Insert the optional interface board into the 
slot as shown in the diagram.  When the 
interface board has reached the back, push 
it again to ensure it is pushed fully back. 

1. Interface board 

 

 

Caution:

 

•

  Electronic components are susceptible to damage by static 

electricity.  Remove static charge from your clothes and body by 
touching your hands to the board box before you touch the network 
interface board. 

Step 3 : 

Fasten the two interface mounting screws. 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments