manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 63 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 63

Daily Maintenance 

Operation Instructions Rockhopper Printer

 

 

Page 

63

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

 

ConfirmChange               Yes 

 

 

Step 8 :

 

 
Press the 

[Value/+]

 or 

[Value/-]

 key to select 

“Yes” and press ENTER. 

 

Remove Cart 

 

 

Step 9 :

 

 
Remove ink cartridges from the slot. 
 

 
Set Wash Cart 
 
Head Wash 

 

Step 10 :

 

 
Insert the cleaning cartridge to the ink cartridge 
slots.  Use the special Eco-solvent Transition 
Liquid when changing to Eco-solvent ink. 
The head wash starts when the cleaning 
cartridge is inserted.  The cleaning period is 
approximately 15 minutes.

 

 
Remove Wash Cart 
 

 

Step 11 :

 

 
Remove the cleaning cartridge from the slot. 
 

 
Head Wash 
 

 

Step 12 :

 

 
The rest of the cleaning fluid in the printer unit is 
discharged when the cleaning cartridge is 
removed. 

 
Change Waste ink 
 

 

Step 13 :

 

 
Empty the waste ink bottle from the printer unit. 
 

 
Change Tank ?                Yes
 

 

Step 14 :

 

 
Press the 

[Value/+]

 or 

[Value/-]

 key to select 

“Yes” and press ENTER. 

 

 
ConfirmChange                        
Yes 
 

 

Step 15 :

 

 
Press the 

[Value/+]

 or 

[Value/-]

 key to select 

“Yes” and press ENTER. 
 

 
[YMCK] Discharged 
 

 

Step 16 :

 

 
If the cassettes that have been removed are 
DYE ink cassettes, now insert PIGMENTED ink 
cassettes or ECO-SOLVENT ink cassettes. 
If the cassettes that have been removed are 
PIGMENTED ink cassettes, now insert DYE ink 
cassettes or ECO-SOLVENT ink cassettes. 
 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments