manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 33 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 33

Installation Procedures 

Operation Instructions Rockhopper Printer

 

 

Page 

33

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

CONNECTING THE POWER CABLE / DISCONNECT DEVICE 

1) Make sure the printer’s power switch is turned OFF. 

2) Make sure the power of the Heating System and the Roll Take-Up System are turned 

OFF. 

3) Plug the printer-end of the power cable into the connector at the back of the printer. 

4) Connect the cable of the Roll-Take-Up System with the Printer body. 

5) Plug the other end of the power cable into an electrical outlet of the correct voltage and 

with a proper grounding. 

•

 

Power supply:

 

- Voltage: 

200 to 240 VAC or 100 to 120 VAC 

- Frequency: 

50/60 Hz ± 1 Hz 

- Current: 

< 10 A (110 V) 

< 5 A (220 V) 

 

 

Note: 

•

  When you turn off the power, please note that your printer needs a 

few seconds to perform its shut down sequence. 

•

  To this end, wait for at least five seconds to switch the printer on 

again. 

•

  The disconnect device is the plug on the power supply cord. 

 
 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments