manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 67 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 67

Daily Maintenance 

Operation Instructions Rockhopper Printer

 

 

Page 

67

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

 

 

Caution: 

•

  The edge of the cutting blade is very fragile, while replacing it, handle 

it with care. 

 

Step 4: 

Put the head manually back into its capping position, and turn the power switch ON. 
 

 

Note:

 

•

  Durability of the cutting blade may differ depending on the kind or 

thickness of the media and used environment.  We recommend 
purchasing a spare cutting blade so that you always have a spare 
blade at hand. 

 

 

Important:

 

If you don’t have a new sheet-off blade available to replace your 
blade, you can temporarily switch off the automatic sheet-off. 

Press menu 

À

 until you see Function. 

Press Enter Function Ink Dry Time. 
Press menu 

À

 until you see “Media Cut : ON” 

Press value + or value -: “Media Cut : OFF” 
Press Enter 
Press Back 

½½

 2 times to go back to ONLINE Level.

 

 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments