manualshive.com logo in svg

MUTOH ROCKHOPPER 48 inch, Operation Instructions Manual, Page: 64 / 78

Share
Download
MUTOH ROCKHOPPER 48 inch Operation Instructions Manual Download Page 64

Daily Maintenance 

Operation Instructions Rockhopper Printer

 

 

Page 

64

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

 

 

Important :

 

 
After using Eco-Solvent ink it is not possible to change to other type of ink 
(pigmented and dye Inks).

 

 

 
Ink Refill                            4M
 
Ink Refill                            3M
 
Ink Refill                            2M
 
Ink Refill                            1M
 
Ink Refill                            0M
 
Ink Refill                            4M
 
Ink Refill                            3M
 
Ink Refill                            2M
 
Ink Refill                            1M
 
Ink Refill                            0M
 

 

Step 17 :

 

 
The initial fill is executed when installing 
cartridges. 
The display will show the following messages :

 

 

Plot OK 

 

 

Step 18 :

 

 
After filling, the display will show the following 
message : 

 

 

 

Note :

 

 

•

  The cleaning cartridge is one time use only. 

 

•

  Only recommended ink cassettes can be used.  The also need to be 

turned in the proper direction for insertion. 

 

•

  Ink cassettes should be used within two years of the date that is 

printed on the package.  Cassettes that have been loaded into the 
printer should be replaced within six months. 

 

 
 

Summary of Contents for ROCKHOPPER 48 inch















































































Reviews:

No comments