manualshive.com logo in svg

Motorola AP 5131 - Wireless Access Point, Product Reference Manual, Page: 22 / 698

Share
Download
Motorola AP 5131 - Wireless Access Point Product Reference Manual Download Page 22

AP-51xx Access Point Product Reference Guide

1-6

For detailed information on locating the access point’s MAC addresses, see 

Viewing WAN Statistics 

on page 7-2

 and 

Viewing LAN Statistics on page 7-6

. For information on access point MAC address 

assignments, see 

AP-51xx MAC Address Assignment on page 1-27

.

1.2.3 Multiple Mounting Options

The access point rests on a flat surface, attaches to a wall, mounts under a ceiling or above a ceiling 
(attic). Choose a mounting option based on the physical environment of the coverage area. Do not 
mount the access point in a location that has not been approved in an either an AP-5131 or outdoor 
AP-5181 radio coverage site survey. 

For detailed information on the mounting options available , see 

Mounting an AP-5131 on page 2-13

 

or 

Mounting an AP-5181 on page 2-24

.

1.2.4 Antenna Support for 2.4 GHz and 5.2 GHz Radios

The access point supports several 802.11a and 802.11b/g radio antennas. Select the antenna best 
suited to the radio transmission requirements of your coverage area. 

For an overview of the Radio 1 (2.4 GHz) and Radio 2 (5.2 GHz) antennas supported on the access 
point’s 

Reverse SMA (RSMA)

 connectors, see 

Antenna Specifications on page A-5

. The AP-5181 

model access point uses an antenna suite primarily suited for outdoor use.

1.2.5 Sixteen Configurable WLANs

A 

Wireless Local Area Network (WLAN)

 is a data-communications system that flexibly extends the 

functionalities of a wired LAN. A WLAN does not require lining up devices for line-of-sight 
transmission, and are thus, desirable for wireless networking. Roaming users can be handed off from 
one access point to another like a cellular phone system. WLANs can therefore be configured around 
the needs of specific groups of users, even when they are not in physical proximity. Sixteen WLANs 
are configurable on each access point. 

To enable and configure WLANs on an access point radio, see 

Enabling Wireless LANs (WLANs) on 

page 5-27

.

1.2.6 Support for 4 BSSIDs per Radio

The access point supports four BSSIDs per radio. Each BSSID has a corresponding MAC address. The 
first MAC address corresponds to BSSID #1. The MAC addresses for the other three BSSIDs (BSSIDs 
#2, #3, #4) are derived by adding 1, 2, 3, respectively, to the radio MAC address.

Summary of Contents for AP 5131 - Wireless Access Point



























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments