Motion Control Engineering Nidec iControl, User Manual, Page: 443 / 453

Index-4 Manual # 42-02-2223
Counterweight Learn procedure 3-11
Coupling rotational ratio 2-18
CP INSP. DISABLED message 6-20
Creating a Configuration file 8-21
Creating a new LAN connection 8-12
Crosshead Deflection Load Weigher 4-30
CT INSP. DISABLED message 6-23
CTEX NO CWI CFG ERROR message 6-22
Current Hold Time 4-25
Current Limiting 4-14
D
DAC Offset Status test point, description 9-3
DAC, verifying DAC conversion 2-34
DBD Mode Activated message 6-24
DBD PHE Antinuisance 6-24
DCAB, Door Contact Access Bottom input 6-112, 9-10
DCAT, Door Contact Access Top input 6-112, 9-10
DCL, Door Close Limit input 6-110, 9-7
DCMS, Door Contact Main String input 6-112, 9-10
Dead zone, adjusting for final stop 4-26
Deceleration parameter 4-13
Deceleration rate, bunching up of 4-15
Default IP Addresses
iBox settings 7-8
default parameter settings, saving 8-20
Demand Down Peak Mode message 6-24
Demand Up Peak Mode message 6-24
DETS, Down Emergency Terminal Limit switch input 6-111,
9-8
Direct connections ??–8-11
connecting 8-10
creating 8-8
Dispatcher = Car ‘n’ message 6-24
Display contrast, iBox control 7-3
DLAB, Door Lock Access Bottom input 6-112, 9-10
DLAT, Door Lock Access Top input 6-112, 9-10
DLM, Down Leveling Marker Sensor input 6-110, 9-7
DLMS, Door Lock Main String input 6-112, 9-10
DN ETS POSITION FAULT message 6-25
DN NTSn L1 SPEED FLT message 6-26
DN NTSn L2 SPEED FLT message 6-26
DN NTSn POSITION FLT message 6-26
DNT1, Down Slowdown Limit switch #1 input 6-111, 9-8
DNT2, Down Slowdown Limit switch #2 input 6-111, 9-8
DNT3, Down Slowdown Limit switch #3 input 6-111, 9-8
DNT4, Down Slowdown Limit switch #4 input 6-111, 9-8
DNT5, Down Slowdown Limit switch #5 input 6-111, 9-8
DNTD, Down Normal Limit Direction switch input 6-111, 9-8
docking and undocking windows in iView 8-35
DOL, Door Open Limit input 6-110, 9-7
DOOR LK CLIPPED G200 message 6-25
DOOR LK CLIPPED L200 message 6-25
Door Lock Clipped Greater than 200fpm message 6-25
Door Lock Clipped Less than 200fpm message 6-25
DOOR LOCK OPENED message 6-25
Door operator, preparing for final adjustments 3-11
Door parameters, verifying 3-8
Doors Locked, iBox status LED 7-10
DOWN DIR LIMIT OPEN message 6-25
Down Direction Limit Open message 6-25
Down Emergency Switch Shutdown message 6-25
Down Emergency Terminal Switch Position Fault message 6-
25
DOWN ETS SHUTDOWN message 6-25
Down Normal Terminal ’n’ Level 1 Speed Fault message 6-26
Down Normal Terminal ’n’ Level 2 Speed Fault message 6-26
Down Normal Terminal ’n’ Position Fault message 6-26
Down switch, iBox control 7-11
Down, iBox status LED 7-10
DP1-, Position Encoder input 6-109, 9-6
DP1+, Position Encoder input 6-109, 9-6
DP2-, Position Encoder input 6-109, 9-6
DP2+, Position Encoder input 6-109, 9-6
DPM, Door Position Monitor input 6-110, 9-7
Drive At Speed Fault message 6-26
Drive Communication Fault message 6-27
Drive Communication Warning message 6-27
Drive Connections, iBox 9-11
DRIVE ENABLE FDBK FLT message 6-27
Drive Enable Feedback Fault message 6-27
Drive Enable Status test point, description 9-3
Drive error, clearing 2-29, 9-67
DRIVE FAULT message 6-27
Drive Fault message 6-27
Drive Inspection Overspeed Fault message 6-27
DRIVE IOS FAULT message 6-27
Drive IOS Limit test point, description 9-4
Drive IOS Param Limit test point, description 9-4
Drive Motor/Encoder Setup 9-69
Drive On Fault message 6-28
Drive On, iBox status LED 7-10
Drive Parameters Quick Reference, Magnetek 9-45, 9-52
Drive Parameters Quick Reference, TORQMAX 9-71
Drive Ready Fault message 6-28
Drive Ready On Fault message 6-28
Drive Start Failure message 6-28
Driver VDC 5-13
DRO fault 4-18
DRO fault, empty car test 3-13
Drop delay, adjusting for final stop 4-27
Dual Channel QUAD Fault message 6-29
DUAL CHANNEL QUAD FLT message 6-29
DZ, Door Zone Sensor input 6-110, 9-7
E
Earthquake (EQ) sensor 3-6
Earthquake board power supply OFF message 6-29
Earthquake board power supply ON message 6-29
Earthquake Board Quick Reference 6-94
Earthquake Emergency Stop message 6-29
Earthquake Operation (Counterweight) message 6-29
Earthquake Operation (Seismic Switch) message 6-29
Earthquake Operation Activated message 6-29
Earthquake Operation Deactivated message 6-29
Earthquake profile 4-13
Earthquake Reduce Speed message 6-30
Earthquake reset button OK message 6-30
Earthquake reset button stuck ON message 6-30
EARTHQUAKE RUN message 6-30