10
ENGLISH
7RUHPRYHWKHGLVFIROORZWKHLQVWDOODWLRQSURFHGXUHLQ
reverse.
NOTE:
8VHVDQGHUDFFHVVRULHVVSHFL¿HGLQWKLVPDQ
-
XDO7KHVHPXVWEHSXUFKDVHGVHSDUDWHO\
OPERATION
WARNING:
It should never be necessary to
force the tool.
The weight of the tool applies ade-
TXDWHSUHVVXUH)RUFLQJDQGH[FHVVLYHSUHVVXUH
FRXOGFDXVHGDQJHURXVZKHHOEUHDNDJH
WARNING:
ALWAYS replace wheel if tool is
dropped while grinding.
WARNING:
NEVER bang or hit grinding disc
or wheel onto work.
WARNING:
Avoid bouncing and snagging
the wheel, especially when working corners,
sharp edges etc.
7KLVFDQFDXVHORVVRIFRQWURODQG
NLFNEDFN
WARNING:
NEVER use tool with wood cutting
blades and other saw blades.
6XFKEODGHVZKHQ
XVHGRQDJULQGHUIUHTXHQWO\NLFNDQGFDXVHORVVRI
FRQWUROOHDGLQJWRSHUVRQDOLQMXU\
CAUTION:
Never switch on the tool when it
is in contact with the workpiece, it may cause an
injury to operator.
CAUTION:
Always wear safety goggles or a
face shield during operation.
CAUTION:
After operation, always switch off
the tool and wait until the wheel has come to a
complete stop before putting the tool down.
CAUTION:
$/:$<6KROGWKHWRRO¿UPO\ZLWK
one hand on housing and the other on the side
handle.
Grinding and sanding operation
Ź
Fig.11
7XUQWKHWRRORQDQGWKHQDSSO\WKHZKHHORUGLVFWRWKH
workpiece.
In general, keep the edge of the wheel or disc at an
DQJOHRIDERXWWRWKHZRUNSLHFHVXUIDFH
'XULQJWKHEUHDNLQSHULRGZLWKDQHZZKHHOGRQRW
ZRUNWKHJULQGHULQIRUZDUGGLUHFWLRQRULWPD\FXWLQWR
WKHZRUNSLHFH2QFHWKHHGJHRIWKHZKHHOKDVEHHQ
URXQGHGRIIE\XVHWKHZKHHOPD\EHZRUNHGLQERWK
IRUZDUGDQGEDFNZDUGGLUHFWLRQ
Operation with abrasive cut-off /
diamond wheel
Optional accessory
WARNING:
When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
,QVRPH(XURSHDQFRXQWULHVZKHQXVLQJDGLDPRQG
ZKHHOWKHRUGLQDU\JXDUGFDQEHXVHG)ROORZWKH
UHJXODWLRQVLQ\RXUFRXQWU\
WARNING:
NEVER use cut-off wheel for side
grinding.
WARNING:
Do not "jam" the wheel or apply
excessive pressure. Do not attempt to make an
excessive depth of cut.
Overstressing the wheel
LQFUHDVHVWKHORDGLQJDQGVXVFHSWLELOLW\WRWZLVWLQJ
RUELQGLQJRIWKHZKHHOLQWKHFXWDQGWKHSRVVLELOLW\
RINLFNEDFNZKHHOEUHDNDJHDQGRYHUKHDWLQJRIWKH
PRWRUPD\RFFXU
WARNING:
Do not start the cutting operation
in the workpiece. Let the wheel reach full speed
and carefully enter into the cut moving the tool
forward over the workpiece surface.
The wheel
PD\ELQGZDONXSRUNLFNEDFNLIWKHSRZHUWRROLV
started in the workpiece.
WARNING:
During cutting operations, never
change the angle of the wheel.
3ODFLQJVLGHSUHVVXUHRQ
WKHFXWRIIZKHHODVLQJULQGLQJZLOOFDXVHWKHZKHHOWR
FUDFNDQGEUHDNFDXVLQJVHULRXVSHUVRQDOLQMXU\
WARNING:
A diamond wheel shall be oper-
ated perpendicular to the material being cut.
Ź
Fig.12:
1.
/RFNQXW
2.
$EUDVLYHFXWRIIZKHHOGLD
-
mond wheel
3.
,QQHUÀDQJH
4.
:KHHOJXDUG
IRUDEUDVLYHFXWRIIZKHHOGLDPRQGZKHHO
$VIRUWKHLQVWDOODWLRQIROORZWKHLQVWUXFWLRQVIRU
depressed center wheel.
The direction for mounting the lock nut and the
LQQHUÀDQJHYDULHVE\ZKHHOW\SHDQGWKLFNQHVV
5HIHUWRWKHIROORZLQJ¿JXUHV
)RUPPƎPRGHO
When installing the abrasive cut-off wheel:
Ź
Fig.13:
1.
/RFNQXW
2.
$EUDVLYHFXWRIIZKHHO
7KLQQHUWKDQPP
3.
$EUDVLYHFXW
RIIZKHHOPPRUWKLFNHU
4.
Inner
ÀDQJH
When installing the diamond wheel:
Ź
Fig.14:
1.
/RFNQXW
2.
Diamond wheel (Thinner
WKDQPPƎ
3.
Diamond wheel (4mm
ƎRUWKLFNHU
4.
,QQHUÀDQJH
)RUPPƎPPƎ
model
When installing the abrasive cut-off wheel:
Ź
Fig.15:
1.
/RFNQXW
2.
$EUDVLYHFXWRIIZKHHO
7KLQQHUWKDQPP
3.
$EUDVLYHFXW
RIIZKHHOPPRUWKLFNHU
4.
Inner
ÀDQJH
