manualshive.com logo in svg

LSIS XGB Series, User Manual, Page: 403 / 618

Share
Download
LSIS XGB Series User Manual Download Page 403

Chapter 11 RTD Input Option Board (XBO-RD01A)

 

 

11.4 Temperature Conversion Characteristic 

 

Since RTD sensor has non-linear characteristic, RTD input module executes linearization per each 
section. 
The graph below is an example to describe the linearization process and is different with graph about 
actual sensor temperature input.     

 

   

(1) PT100: JIS1604-1997 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 

 

 
(2) JPT100: JIS C1604-1981, KS C1603-1991 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 

 

 

 

Non-linear characteristics: The resistance-temperature characteristics for RTD sensor are presented 
with table (JIS C1604-1997). This characteristics table displays resistance value of the sensor to 
temperature, namely, the change of the resistance value per increment of 1

℃

. When the 

temperature  is  changed  by 1

℃

, the change of resistance  is  not in constant width but in different 

width per section, which is called the non-linear characteristics.   

600.0

℃

 

0.0

℃

 

-

200.0

℃

 

18.52 

Measured temperature 
Resistance 

(Ω) 

 

Temperature

 (

℃

) 

100 

313.71 

Linearized sensor characteristics 

 

 

 

Real Sensor characteristics

 

0.0

℃

 

-

 

17.14 

Measured temperature 
Resistance 

(Ω)

 

Temperature

 (

℃

) 

100 

317.28 

Linearized sensor characteristics

 

Real sensor characteristics

 

600.0

℃

 

Remark 

11 - 5 

 

Summary of Contents for XGB Series











































































































































































































































































































































































































































































































































































































































Reviews:

No comments