manualshive.com logo in svg

LSIS XGB Series, User Manual, Page: 151 / 618

Share
Download
LSIS XGB Series User Manual Download Page 151

XGB Analog edition manual

 

 

 

5.3 Function 

 

5.3.1 Disconnection detection function 

 

Thermocouple input module has a function to detect the disconnection and display it. 
That the module detects and displays disconnection means that the following cabling path would have 

partially bad connection, which requires taking measures   

 

(1) Disconnection occurs between a sensor used/compensating cable and module, LED(ALM) flickers 

every second and generates error code.   

 

(2) Disconnection can be detected by channels. However, it is available for the only channel(s) 

designated for operation. LED (ALM) is commonly used for every channel. It flickers in case even 
only one channel is disconnected.   

 

Thermocouple connection 

status 

Channel 

run 

  ALM LED 

status 

Disconnection 

flag 

Normal 

Run 

Off 

Off 

Stop 

Off 

Off 

Thermocouple 

disconnection 

Run 

Flickering (1s) 

On 

Stop 

Off 

Off 

 

(3) In case disconnection occurs, disconnection flag of each channel will be turned on and in case 

disconnection is canceled, it will be turned off.   

Disconnection flag 

Contents 

U0x.01.4 

Ch. 0 disconnection 

U0x.01.5 

Ch. 1 disconnection 

U0x.01.6 

Ch. 2 disconnection 

U0x.01.7 

Ch. 3 disconnection 

 

(4) When disconnection occurs, the min value among range is displayed.   

 

Type 

Displayed temperature in case of 

disconnection 

K type 

-270.0

℃

 

J type 

-210.0

℃

 

T type 

-270.0

℃

 

R type 

-50.0

℃

 

 
 

Type 

Displayed value in case of disconnection 

0 ~ 100

㎷

 

(XBF-TC04B) 

0 

5 - 14 

 

 

Summary of Contents for XGB Series











































































































































































































































































































































































































































































































































































































































Reviews:

No comments