Lexmark X925 7541-03 series Service Manual Download Page 137

Page: 137 / 500

Diagnostic information

2-99

7541-03x

Go Back

Wrong paper size service check - tray1

Wrong paper size service check - tray2

Step

Action and questions

Yes

Check the size indicator on the front of the tray. Is it set
to the correct size?

Go to step 3.

Go to step 2.

Set the indicator to the correct size. Did this fix the
issue?

Problem solved

Go to step 3.

Is the sensor cable properly connected to the sensor
and engine board?

Go to step 5.

Go to step 4.

Connect the cable. Did this fix the problem?

Problem resolved

Go to step 5.

Check the cable for continuity. Is there continuity?

Go to step 7.

Go step 6.

Replace the cable. Did this fix the issue?

Problem resolved

Go to step 7.

Replace the sensor. Did this fix the issue?

Problem resolved

Go to step 8.

Replace the engine board. Did this fix the issue.

Problem resolved

Contact your
second level
support.

Step

Action and questions

Yes

Remove the tray, and move the paper size guides to
different positions. Are the size pins moving when the
length guide is moved?

Go to step 3.

Go to step 2.

Try a different paper standard tray. Did this fix the
problem?

Problem resolved

Go to step 3.

Check the sensor cables for proper connection to the
sensors and engine controller board. Are they properly
connected?

Go to step 5.

Go to step 4.

Properly connect the cables. Did this fix the problem?

Problem resolved

Go to step 5.

Replace the sensors. Did this fix the problem?

Problem resolved

Go to step 6.

Replace the engine controller board. Did this fix the
problem?

Problem resolved

Contact your
second level
support.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands