Lexmark X925 7541-03 series Service Manual Download Page 145 | Manualshive

Page: 145 / 500

background image

Diagnostic aids

3-7

7541-03x

Go Back

Previous

Next

Accessing the service menus

There are different test menus that can be accessed during POR to identify problems with the printer.

Diagnostics menu

1. Turn off the printer.
2. Press and hold

3

and

6

.

3. Turn on the printer.
4. Release the buttons when the splash screen

appears.

The Diagnostics menu group
contains the settings and
operations used while
manufacturing and servicing the
printer.

For more information, see

“Diagnostics mode” on
page 3-18

.

Configuration menu

1. Turn off the printer.
2. Press and hold

2

and

6

.

3. Turn on the printer.
4. Release the buttons when the splash screen

appears.

The Configuration menu group
contains a set of menus, settings,
and operations which are
infrequently required by a user.
Generally, the options made
available in this menu group are
used to configure a printer for
operation.

See

“Configuration Menu” on

page 3-9

for more information.

Network SE menu

While in Network/Ports Menu, press and hold

9

,

7

,

and

6

.

SE menu

At the printer, perform the following steps:

1. In the Admin menu, navigate to

Network

>

Ports

>

Standard Network

>

Std Network

Setup

menu.

2. Press and hold

9

,

7

, and

6

.

3. Release the buttons when the

Network SE

Menu

appears.

From a browser, add “/se” to the device IP address
(for example: http://158.183.3.2/se)

THe MFP does not need to be
restarted to enter this menu.

Invalid engine code
mode

1. Turn off the printer.
2. Press and hold

3

,

4

,and

6

(E+N+G).

3. Turn on the printer.
4. Release the buttons when the splash screen

appears.

This mode is used if the machine
has invalid code and needs the
correct code loaded. After
entering this mode, the firmware
code can be updated.

«
...
143
144
145
146
147
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: IBM Pages: 112

Brand: Xerox Pages: 40

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

VarioPrint 6000 MICR series

Brand: Oce Pages: 264

Brand: Oce Pages: 194

Brand: Z Corporation Pages: 99

Brand: Canon Pages: 542

Brand: Lexmark Pages: 2

Brand: Ricoh Pages: 781

Brand: Oki Pages: 128

Brand: AstroJet Pages: 97

Brand: Sindoh Pages: 33

ThermalTronix TT-1260S-UTCM

Brand: Intellisystem Pages: 18

Brand: Pantum Pages: 164

Brand: Oki Pages: 276

Brand: Brightek Pages: 8

Brand: Lexmark Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands