manualshive.com logo in svg

Lexmark X925 7541-03 series, Service Manual

The Lexmark X925 7541-03 series is a high-performance printer designed to meet all your business needs. With our Service Manual, you can easily troubleshoot any issues and perform maintenance tasks hassle-free. Download this invaluable manual for free at manualshive.com and ensure the optimal performance of your Lexmark printer.

Share
Download
background image

Diagnostic aids 

3-11

7541-03x

Go Back

Previous

Next

Reset Transfer Belt Counter

This menu item is used to reset the transfer belt counter for the print engine when a Transfer Belt is installed.

1.

Touch the menu item. A “Reset Fuser Counter” button is displayed.

2.

Touch that button to reset the counter.

USB Scan to Local

When set to Off, this setting tells the USB device driver to enumerate as a USB Simple device. When this is set 
to on, USB device driver enumerates as a USB Composite device (multiple interfaces).

Black Only Mode

When this setting is set to On the printer prints only grayscale printing. The default is Off. The result is similar to 
setting Print Mode to Black Only.

Note:  

This setting appears only when the PJL Password Environment variable is set to 0.

Print Quality Pages

The Print Quality Test consists of five pages. Pages one and two contain a mixture of graphics and text. The 
remainder of the pages only contain graphics. Use this test to identify print quality problems. The Test Pages 
must be printed on A4, Legal, or Letter paper.

Fuser Speed

Use this setting if the device is encountering a shock line issue. After adjusting the setting, the device will print 
the 

Print Quality Pages

. It is recommended that this menu setting is used under the guidance of your second 

level of support.

Reports

From this menu you can print the Menu Settings Page or the Event Log. 

(Will event log be added?)

Color Trapping

Color trapping is an aid to graphics and text. When text or graphics appear over other colors, a misalignment 
may allow white paper to show through at the borders of the colors. Color trapping increases the amount of color 
under the upper image so a slight misalignment does not show. This affects PCL 5e, PCL XL, PDF, and 
PostScript printing. 

Increasing the value increases the amount of color remaining beneath the black content, in increments of 1/600 
of an inch.

1.

Select 

Color Trapping

 from the Configuration menu. 

2.

Select the value or 

Off

. The range is 1 to 5, and the default value is 2.

Press (+) to increase the value.

3.

Press 

Check

 to accept.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Canon PIXMA MX922 Setting Up preview
PIXMA MX922
Brand: Canon Pages: 29
Canon PIXMA MX410 Series Network Setup Troubleshooting preview
PIXMA MX410 Series
Brand: Canon Pages: 46
Canon BJC-S9000 Quick Start Manual preview
BJC-S9000
Brand: Canon Pages: 65
Canon PIXMA MX372 Getting Started Manual preview
PIXMA MX372
Brand: Canon Pages: 4
Canon MX530 series Setting Up preview
MX530 series
Brand: Canon Pages: 2
Canon BJC-50 Datasheet preview
BJC-50
Brand: Canon Pages: 2
Canon Sure shot 80 tele Remote Ui Manual preview
Sure shot 80 tele
Brand: Canon Pages: 39
Canon BJC6500 - BJC 6500 Color Inkjet Printer Paper Manual preview
BJC6500 - BJC 6500 Color Inkjet Printer
Brand: Canon Pages: 6
Canon G600 Series Getting Started preview
G600 Series
Brand: Canon Pages: 20
Canon imagePROGRAF iPF6450 Manual preview
imagePROGRAF iPF6450
Brand: Canon Pages: 35
Canon PIXMA MX340 Series Connection Manual preview
PIXMA MX340 Series
Brand: Canon Pages: 11
Canon PIXMA MX340 Series Network Installation Manual preview
PIXMA MX340 Series
Brand: Canon Pages: 16
Canon imagePROGRAF iPF6300S Setup Manual preview
imagePROGRAF iPF6300S
Brand: Canon Pages: 12
Canon MP980 series Connection Manual preview
MP980 series
Brand: Canon Pages: 19
Canon MP980 series Quick Start Manual preview
MP980 series
Brand: Canon Pages: 101
Canon iP4700 - PIXMA Color Inkjet Printer Getting Started preview
iP4700 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 28
Canon i 320 Setup Instructions preview
i 320
Brand: Canon Pages: 2
Canon CX-G6400 Manual preview
CX-G6400
Brand: Canon Pages: 35

Brands by name

Popular brands

Load more brands