Lexmark X925 7541-03 series Service Manual Download Page 140

Page: 140 / 500

3-2

Service Manual

7541-03x

Go Back

Understanding the home screen

Buttons appearing on the home screen may vary depending on home screen customization settings.

Possible buttons and icons on the home screen

Item

Description

Copy

Opens the Copy menu

E-mail

Opens the E-mail menu

Scan

Opens the Scan menu

Fax

Opens the Fax menu

Menus

Opens the administrative menus when

Ready

appears on the display

FTP

Opens the FTP menu

Note:

This option must be set up by a system administrator before it

appears on the display.

Status message bar

Shows the current printer status such as Ready or Busy

Note:

Make sure Ready appears before performing any printer task.

•

Shows printer conditions such as

Toner Low

Cartridge Low

•

Shows intervention messages and gives instructions for the printer
to continue processing

Status/Supplies

Displays a warning or error message whenever the printer requires
intervention to continue

processing

Touch this to access the messages screen for more information on the
message, and how to clear it.

Tips

Opens context-sensitive Help information on the touch screen

Note:

All menus have a Tips button.

USB

Displays files on a flash drive

Bookmarks

Allows you to create, organize, and save a set of bookmarks (URLs) into a
tree view of folders and file links

Held Jobs

Displays all held jobs

Change Language

(not pictured)

Allows you to change the primary language and reports on the display,
and will remain in effect until changed

Release Held Fax

(not pictured)

If this button is shown, then there are held faxes with a scheduled hold
time previously set. To access the list of held faxes, touch this button.

Lock Device

(not pictured)

This button appears when the printer is unlocked and the Printer Lockout
Personal Identification Number (PIN) has been set.

Touching this button opens a PIN entry screen. Enter the correct PIN to
lock the operator panel.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands