Lexmark X925 7541-03 series Service Manual Download Page 153 | Manualshive

Page: 153 / 500

background image

Diagnostic aids

3-15

7541-03x

Go Back

Previous

Next

Action for Prompts

This setting enables users to have the printer resolve media change prompt situations automatically. Such
prompts occur when the selected media for the job is not available when the job prints. This setting applies only
to jobs that cannot be parked.

•

Prompt user (default setting)—The user must respond to the prompt and choose one of the following
options each time.

•

Continue—The job prints on the closest available media, and the printer preserves the requested size and
type specifications (e.g., Bond or Transparency). If the available media is smaller than the requested size,
the printer crops the print image as needed.

•

Use Current—The job prints on the media currently available and uses the size and type specifications of
the available media instead of the original job. If the media is smaller than the requested size, the printer
crops the print image as needed.

Jobs On Disk

This setting appears only if a hard disk is installed. Jobs can be deleted from the hard disk. Settings are Delete
and Do Not Delete (default). The Delete setting does not affect Print and Hold or parked jobs.

Disk Encryption

This setting appears only if a hard disk is installed, the disk is not read only, and Disk Encryption is enabled.

Warning:

When the settings are changed, all data on the hard disk is deleted.

Erase all information on Disks

This setting performs a wipe of the printer hard disk, erasing all data.

Warning:

Wipe Disk deletes all data on the printer hard disk, including downloaded fonts, macros, and held

jobs. Do not initiate a disk wipe if you have information on the printer that you want to save.

•

Wipe disk (fast)—This is a single-pass wipe that overwrites all data and the file system. This wipe is faster
but less secure since it is possible to retrieve the deleted data with forensic data retrieval techniques.

•

Wipe disk (secure)—This multiple-pass wipe overwrites all data without rewriting the file system. This wipe
is DoD 5220.22-M compliant since the deleted data is irretrievable.

Wipe All Settings

Use this menu item to remove all information, settings, solutions, and jobs from a disk.

Font Sharpening

Font Sharpening allows the user to adjust the value of the high frequency screens used for font data. For
example, if the value is 24, all fonts 24 points and less use the high frequency screens. The default value is 24.

This feature works only in PostScript emulation.

Require Standby

If set to Off, this setting disables Standby Mode in the General Settings menu.

UI Automation

«
...
151
152
153
154
155
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

Brand: DASCO Pages: 2

COLOR SYSTEM 110

Brand: Oce Pages: 392

Brand: Oki Pages: 104

KX-MC6040 - Color Laser Multi-Function...

Brand: Panasonic Pages: 24

Brand: Canon Pages: 2

imageRUNNER C3480

Brand: Canon Pages: 92

Brand: Oki Pages: 328

Brand: Citizen Pages: 133

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands