Lexmark X925 7541-03 series Service Manual Download Page 100

Page: 100 / 500

2-62

Service Manual

7541-03x

Go Back

C. Collecting the settings from the menu settings page

Note:

The menu settings page is different for each printer. For more information see the

User’s Guide

. Your

next level of support will tell you which page they want to see.

Copying the menu settings page from the Embedded Web Server (EWS)

Note:

Make sure your printer is connected to a network or to a print server.

From a Web browser, type

http://printer_IP_address

, and then press

Enter

Click

Settings

, and then select one of the settings page from the links shown on the page.

Copy all information, and then save it as a text file.

E-mail the text file to your next level of support.

Printing the menu settings page

From the home screen, navigate to

Reports

Menu Settings Page

Print the menu settings page, and then use Scan to E-mail to send it to your next level of support.

D. Collecting information from the user

Ask the user for information about the following:

•

Print job being run

•

Operating system used

•

Print driver used

•

Other information on what was happening when the 9yy error occurred.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands