Lexmark X925 7541-03 series Service Manual Download Page 134

Page: 134 / 500

2-96

Service Manual

7541-03x

Go Back

Power supply (Dead machine) service check

Note:

Before proceeding, make sure that this is not an issue with the display. Turn the machine on. If the

machine’s fans, and motors start up, it could be an issue with the display.

Step

Action and questions

Yes

Is the power cord connected to the printer and the wall
outlet?

Go to step 3.

Go to step 2

Connect the power cord to the printer and wall outlet.
POR the printer. Did it start?

Problem solved

Go to step 3.

Try a different power cord. Did this fix the problem.

Problem solved

Go to step 4.

Verify that the voltage to the machine is within
spec.110v, ac +/- 10%, 220v, ac +/- 10%. Is the voltage
in within spec?

Go to step 5.

Try a different
power outlet.

Verify that the cables connecting the power inlet, the
switch and secondary power supply are properly
connected.

Go to step 6.

Properly connect
the cables.

Verify that the cables connecting CN02 on the
secondary power supply unit to CN03 on the LVPS are
connected properly.

Go to step 7.

Properly connect
the cables.

Replace the switch. Did this fix the problem.

Problem solved

Go to step 8.

Are the fuses blown on either supply?

Go to step 9.

Go to step 10.

Replace the power supply with the blown fuse. Did this
fix the problem?

Problem solved

Go to step 10

Check CN03 on the scanner power supply for the
following voltages and grounds:

Pins 1,and 2 should be +5V dc

Pins 2 and 4 should be + 24V dc

Pins 5,6,7, and 8 are GND

Are the voltages correct?

Go to step 11.

Replace the
scanner power
supply. See

“Scanner power
supply removal”
on page 4-58

Replace the RIP board. See

“RIP board removal” on

page 4-73

. Did this fix the problem

Problem solved.

Go to step 12

Check CN03 on the low voltage power supply for the
following voltages and grounds:

Pins 4,and 8 should be +5V dc

Pins 2 and 6 should be + 24V dc

Pins 1,3,4, and 7 are GND

Are the voltages correct?

Go to step 13

Replace the
LVPS. See

“Low

volt power
supply removal”
on page 4-51

Replace the printhead controller board. See

“Printhead controller board removal” on page 4-37

Did this fix the problem?

Problem solved.

Contact you next
level support.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands