Lexmark X925 7541-03 series Service Manual Download Page 101 | Manualshive

Page: 101 / 500

background image

Diagnostic information

2-63

7541-03x

Go Back

Previous

Next

900.xx System software error

Notes:

Before troubleshooting:

•

Perform the

“Steps before starting the 9yy service checks” on page 2-60

.

•

Determine the operating system used when the error occured. If possible determine whether a PostScript
or PCL file was sent to the device when the error occured. Ask the customer which Lexmark Solutions
applications are installed on the device.

Step

Action and questions

Yes

No

1

POR the device.

Does the error reoccur?

Go to step 2.

Problem
resolved.

2

• Write down the exact 900.xx error code displayed

on the device.

• Turn the device off.
• Clear the print queues.
• Disconnect all communication cables, and remove

all memory options.

• Remove all ISP and modem cards.
• Restart the device into diagnostic mode.

Does the 900.xx error reoccur during startup?

Go to step 3.

Go to step 6.

3

Check all the cables connected to the RIP board for
proper connectivity.

Are the cables properly connected?

Go to step 5.

Go to step 4.

4

Properly connect the cables to the RIP board. Restart
the device into diagnostic mode.

Does the 900.xx error reoccur during startup?

Go to step 5.

Go to step 6.

5

Replace the RIP board, and restart the device.

Does this fix the problem?

Note:

If an error, different from the original 900.xx, is

displayed, consult the service check for that error.

Problem
resolved.

Go to step 31.

6

Print the following:

• Error log
• Menu settings page
• Network settings page

Does the 900.xx error reoccur while these pages
were printing?

Go to step 31.

Go to step 7.

7

Re-attach the communications cable. Restart the
printer to operating mode. Send the printer a print job.

Does the 900.xx error reoccur?

Note:

Before performing this step, write down this

information about the file being sent to the printer:

• Application used
• Operating system
• Driver type
• File type (PCL, PostScript, XPS, etc.)

Go to step 8.

Go to step 10.

«
...
99
100
101
102
103
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: IBM Pages: 102

Brand: Zmorph Pages: 16

DocuPrint C525 A

Brand: Xerox Pages: 49

DocuPrint C2100

Brand: Xerox Pages: 206

Brand: Xerox Pages: 116

Brand: Xerox Pages: 358

Brand: Xerox Pages: 344

Brand: Xerox Pages: 59

Brand: Xerox Pages: 2

Brand: Xerox Pages: 10

Brand: Xerox Pages: 51

Brand: Xerox Pages: 110

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 8

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

8400B - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 203

3150 - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3117 - Phaser B/W Laser Printer

Brand: Xerox Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands