Lexmark X925 7541-03 series Service Manual Download Page 135

Page: 135 / 500

Diagnostic information

2-97

7541-03x

Go Back

Printhead service check

Transfer belt up down check

Step

Action and questions

Yes

Check the LED for any dirt or toner that may distort the
image. Is the LED dirty?

Go to step 2.

Go to step 3.

Clean the LED. Did this fix the problem?

Problem solved

Go to step 3.

Check the ribbon cable for proper connectivity to the
defective printhead, and the printhead controller
board.Is the cable properly connected?

Go to step 5.

Go to step 4.

Properly connect the cable on both ends. Did this fix
the problem?

Problem solved

Go to step 5.

Check the cable for continuity. Is there continuity?

Go to step 6.

Go to step 7.

Replace the defective cable. Did this fix the problem?

Problem solved

Go to step 7.

Replace the printhead. Did this fix the problem?

Problem solved

Go to step 8.

Replace the printhead controller board. Did this fix the
problem?

Problem solved

Contact you
second level
support.

Step

Action and questions

Yes

Is the transfer belt position sensor actuator jammed or
broken?

Replace the
transfer belt.

Go to step 2.

Is the belt position sensor cable connected to the
sensor and CN9 on the engine board?

Go to step 3

Properly connect
the cable at both
ends.

Replace the belt position sensor. DId this fix the
problem?

Problem solved.

Go to step 4.

Replace the engine board. Did this fix the problem?

Problem solved.

Contact your
second level
support.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands