Lexmark X925 7541-03 series Service Manual Download Page 400 | Manualshive

Page: 400 / 500

background image

4-212

Service Manual

7541-03x

Go Back

Previous

Next

Adjusting ADF magnification

1.

Enter the Diagnostic menu: press and hold

3

and

6

, turn on the printer, and release the buttons when the

splash screen appears.

2.

To print a test page from the Diagnostic menu, navigate to:

REGISTRATION

>

Quick Test

3.

To copy the test page from the Diagnostic menu, navigate to:

SCANNER CALIBRATION

>

Copy Quick Test

.

4.

Navigate to:

SCANNER TESTS

>

ADF Magnification

.

5.

Compare the copy to the original test page, and then adjust the value of the ADF Magnification setting as
needed. If the bottom margin is too small, decrease the value. If the bottom margin is too large, increase
the value.

6.

Touch

Submit

to save your changes.

7.

To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat the
steps as needed.

8.

Once the margins look correct, check the registration of the ADF.

Perform the Copy Quick Test, and then repeat the process if needed.

Adjusting scanner registration

Note:

If the printer menus do not match the following instructions, then contact your next level of support.

1.

Enter the Configuration menu: press and hold

2

and

6

, turn on the printer, and release the buttons when

the splash screen appears.

2.

Navigate to:

Scanner Manual Registration

>

Print Quick Test

3.

Adjust the flatbed:

a.

Place the printed test page facedown on the flatbed scanner glass, and select

Copy Quick Test

.

b.

Compare the copy to the original test page.

c.

Select

Flatbed

, and adjust the left and top margins as needed.

d.

Touch

Submit

to save your changes.

e.

To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.

4.

Adjust the ADF Front:

a.

Place the latest test page face up in the ADF, and select

Copy Quick Test

.

b.

Compare the copy to the original test page.

c.

Select

ADF Front

, and adjust the horizontal adjust and top margins as needed.

d.

Touch

Submit

to save your changes.

e.

To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.

5.

Adjust the ADF Back:

a.

Place the latest test page facedown in the ADF, and select

Copy Quick Test

.

b.

Compare the copy to the original test page.

c.

Select

ADF Back

, and adjust the horizontal adjust and top margins as needed.

d.

Touch

Submit

to save your changes.

e.

To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.

Touch

Back

to return to the Configuration Menu.

«
...
398
399
400
401
402
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: Xerox Pages: 34

Brand: SPRT Pages: 28

Brand: Lanier Pages: 3

Brand: Canon Pages: 797

LASER CLASS 730i

Brand: Canon Pages: 155

Brand: Ricoh Pages: 156

Brand: Xerox Pages: 284

Brand: Sagem Pages: 154

Brand: Wasp Pages: 82

Brand: Xerox Pages: 4

Brand: WOOSIM Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 96

Brand: Brother Pages: 10

Brand: Brother Pages: 11

Brand: Brother Pages: 74

Brand: Brother Pages: 3

Brand: Brother Pages: 20

Brand: Brother Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands