Lexmark X925 7541-03 series Service Manual Download Page 99 | Manualshive

Page: 99 / 500

background image

Diagnostic information

2-61

7541-03x

Go Back

Previous

Next

Warning:

Do not replace the controller board unless directed by your next level of support.

1.

Collect the history information and firmware logs (Fwdebug and logs.tar.gz) from the SE menu.

2.

Collect the settings from the menu settings page.

3.

Collect information from the user.

Note:

Not all of the items can be retrieved from the printer you are working on.

A. Collecting the history information from the SE menu

Note:

Make sure your printer is connected to a network or to a print server.

1.

From a Web browser, type

http://printer_IP_address/se

, and then press

Enter

.

Notes:

•

printer_IP_address

is the TCP/IP address of the printer

•

se

is required to access the printer diagnostic information

2.

Click

History Information

, copy all information, and then save it as a text file.

3.

E-mail the text file to your next level of support.

B. Collecting the firmware logs (Fwdebug and logs.tar.gz) from the SE menu

Notes:

•

Make sure your printer is connected to a network or to a print server.

•

Some printers are designed to restart automatically after a 9yy error. On these printers, you can retrieve
the secondary crash code information using the SE menu.

•

Fwedebugs can also be referred to as LBtrace. If FWEdebugs does not appear in the list, then look for
LBtrace. Mulitple LBtrace logs can appear in the list of links referred to in step 2.

1.

From a Web browser, type

http://printer_IP_address/se

, and then press

Enter

.

2.

Click

List Fwedebugs captured during reboots

. This will provide you a list of the secondary crash codes

retrieved from prior reboots.

Note:

If there are Fwedebugs listed, click

Dump Fwedebug log0

,

Dump Fwedebug log1

, and

Dump

Fwedebug log2

. Clicking these links will dump the debug logs to the computer. Take note of the

destination folder where the logs are saved.

3.

E-mail the logs to your next level of support.

Note:

Some machine SE menus give you the option of clicking

Logs Gzip Compressed

. If this option is

shown in the menu, then click it and retrieve the compressed log file. Take note of the destination folder
where the log file is saved.

«
...
97
98
99
100
101
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: Canon Pages: 86

Brand: Canon Pages: 20

JG Titan MKII V2

Brand: iBox Pages: 5

Brand: Oki Pages: 4

Brand: Lexmark Pages: 2

Brand: Roland Pages: 36

Brand: Microcom Pages: 73

Brand: Oki Pages: 157

Brand: X-media Pages: 10

7760DX - Phaser Color Laser Printer

Brand: Xerox Pages: 4

Brand: Oki Pages: 424

LaserPro X500 III-80Y

Brand: GCC Technologies Pages: 127

Brand: Citizen Pages: 255

Brand: 3D Systems Pages: 29

Brand: Epson Pages: 20

LQ 870 - B/W Dot-matrix Printer

Brand: Epson Pages: 5

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands