manualshive.com logo in svg

Lexmark X925 7541-03 series, Service Manual

The Lexmark X925 7541-03 series is a high-performance printer designed to meet all your business needs. With our Service Manual, you can easily troubleshoot any issues and perform maintenance tasks hassle-free. Download this invaluable manual for free at manualshive.com and ensure the optimal performance of your Lexmark printer.

Share
Download
background image

 

xi

7541-03x

Paperfeed unit component removals

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-178

Separating the MPF tray and main tray paperfeed units  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-178
Main tray paper guide removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-179
Multi-purpose feed tray paper guide removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-181
Paperfeed unit clutch removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-184
Registration sensor (MPF tray) removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-185
Registration sensor actuator removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-185
Static discharge brush removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-186
Torque limiter removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-186
Upper and lower registration springs removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-186

Paperfeed maintenance kit removals

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-188

Pick roll removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-188
Paperfeed roll removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-188
Separator roll removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-189
Registration roll removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-190
MPF roll removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-191
MPF pad removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-193
Exit guide (paper exit) roll removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-196

Option paper feed removals

 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-202

Paper feed roll removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-202
Pick roll removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-202
Separator roll removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-203
Paper size switches removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-203
Paper level sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-204
Transport sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-204
Paper empty sensor removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-205
Paper full sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-205
Option controller board removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-206
Stepper motor removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-206
Tray lift motor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-207
Option door inter lock switch removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-208
Paper feed clutch removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-209

Adjustments

 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-211

Calibrating the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-211

Calibrating the scanner black levels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-211

Adjusting ADF magnification  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-212
Adjusting scanner registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-212

Locations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

5-1

Locations

 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1

Print engine cross section   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1
Flatbed / ADF sensors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3

ADF  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3
Flatbed Sensors   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3

Rip Board connectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-4
Scanner (secondary) power supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-25
Scanner ICC board connectors   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-26
ADF relay card connectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-31
UICC connectors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-34

Option feeder locations

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-35

Option feeder layout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-35
Option board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-36
Option board connector values  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-37
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-37

Preventive maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

6-1

Safety inspection guide

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1

Lubrication specifications

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1

Scheduled maintenance

 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Oki B2200 Specifications preview
B2200
Brand: Oki Pages: 2
EBS 2500 Installation And First Startup preview
2500
Brand: EBS Pages: 4
NCR 7156 Setup And User Manual preview
7156
Brand: NCR Pages: 38
Panasonic KXPX2M - HOME PHOTO PRINTER Guía Rápida preview
KXPX2M - HOME PHOTO PRINTER
Brand: Panasonic Pages: 28
Panasonic KX-P8420 Reference Manual preview
KX-P8420
Brand: Panasonic Pages: 78
Panasonic KX-P7110 Network Setup Manual preview
KX-P7110
Brand: Panasonic Pages: 4
Panasonic KX-P1124 Manual preview
KX-P1124
Brand: Panasonic Pages: 2
Panasonic KX-CL400 Operating Instructions Manual preview
KX-CL400
Brand: Panasonic Pages: 9
Panasonic Jetwriter KX-CL500 User Manual preview
Jetwriter KX-CL500
Brand: Panasonic Pages: 32
TallyGenicom 2440 Quick Start Manual preview
2440
Brand: TallyGenicom Pages: 38
Pantum P3000 Series Maintenance Manual preview
P3000 Series
Brand: Pantum Pages: 94
SATO MN-4203 Specifications preview
MN-4203
Brand: SATO Pages: 2
Kodak 6J7159 Installation Instructions preview
6J7159
Brand: Kodak Pages: 2
2PrintBeta Beta Prusa Standard Assembly Instructions Manual preview
Beta Prusa Standard
Brand: 2PrintBeta Pages: 67
Oki OJ2500 User Manual preview
OJ2500
Brand: Oki Pages: 80
Olivetti d-Copia 45 Operation Manual preview
d-Copia 45
Brand: Olivetti Pages: 246
FOREVER Flex-Soft Quick Start Manual preview
Flex-Soft
Brand: FOREVER Pages: 2
Intellisystem ThermalTronix TT-1025EX-MIL User Manual preview
ThermalTronix TT-1025EX-MIL
Brand: Intellisystem Pages: 11

Brands by name

Popular brands

Load more brands