Lexmark X925 7541-03 series Service Manual Download Page 18

Page: 18 / 500

xviii

Service Manual

7541-03x

Go Back

Preface

This manual contains maintenance procedures for service personnel. It is divided into the following chapters:

General information

contains a general description of the printer and the maintenance approach used to

repair it. Special tools and test equipment, as well as general environmental and safety instructions, are
discussed.

Diagnostic information

contains an error indicator table, symptom tables, and service checks used to

isolate failing field replaceable units (FRUs).

Diagnostic aids

contains tests and checks used to locate or repeat symptoms of printer problems.

Repair information

provides instructions for making printer adjustments and removing and installing

FRUs.

Connector locations

uses illustrations to identify the connector locations and test points on the printer.

Preventive maintenance

contains the lubrication specifications and recommendations to prevent

problems.

Parts catalog

contains illustrations and part numbers for individual FRUs.

Appendix A

contains service tips and information.

Appendix B

contains representative print samples.

Navigation buttons

This manual contains navigation buttons in the right margin of each page, making it easier and quicker to
navigate.

Button

Description

Click

to move the document view backward by one page.

Click

to move the document view forward by one page.

Go Back

Click

to return to the last page viewed.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands