Lexmark X925 7541-03 series Service Manual Download Page 162 | Manualshive

Page: 162 / 500

background image

3-24

Service Manual

7541-03x

Go Back

Previous

Next

Flash Test

This test causes the file system to write and read data on the flash to test the flash.

Warning:

This test destroys all data on the flash because the flash is reformatted at the end of the test.

1.

Select

Flash Test

from DEVICE TESTS From the Diagnostics menu, navigate to:

DEVICE TESTS

>

Flash Test

A

Contents will be lost

warning appears.

2.

To exit the test immediately and return to DEVICE TESTS, select

No

and touch

Submit

. To continue with

the test, select

Yes

and touch

Submit

.

When the test starts, a progress bar appears. The test cannot be stopped or canceled once it has begun.

3.

Once the test is complete, the power indicator turns on solid and a message appears indicating whether
the test passed or failed. Press

Stop

(

X

) to return to DEVICE TESTS.

Input Tray Tests

This test determines if the printer can feed media from any of the paper input sources. Each of the installed
sources is available within the Input Tray Tests menu.

To run the Input TrayTest:

1.

From the Diagnostics menu, touch

INPUT TRAY TESTS

.

2.

Select the input source.

3.

Select either

Single

or

Continuous

.

Note:

If

Single

is selected, no buttons are active while the input device is feeding. If

Continuous

is

selected,

Stop

(

X

) can be pressed to cancel the test.

4.

At the end of the test, the printer returns to the INPUT TRAY TESTS menu.

PRINTER SETUP

Defaults

This setting is used by the printer to determine whether US or non-US factory defaults should be selected. The
following printer settings have different US and non-US values:

Modification of the printer setting Defaults causes the NVRAM space to be restored to the printer’s factory
settings.

Printer default values

US value

Non-US value

Paper Sizes setting in the General Settings menu

U.S.

Metric

Default Paper Size (paper feeding sources which do not have
hardware size sensing capabilities)

Letter

A4

Default Envelope Size

(envelope feeding sources which do not have hardware size
sensing capability)

10 Envelope

DL Envelope

Fax media size

Letter

A4

PCL Symbol Set

PC-8

PC-850

PPDS Code Page

437

850

Universal Units of Measure

Inches

Millimeters

«
...
160
161
162
163
164
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: Malyan Pages: 9

Brand: Xerox Pages: 108

Brand: Oki Pages: 167

Brand: Oki Pages: 116

Brand: Oki Pages: 52

Brand: Oki Pages: 331

Brand: Oki Pages: 36

C5800Ldn Series

Brand: Oki Pages: 143

Brand: Oki Pages: 101

Brand: Oki Pages: 6

Brand: Oki Pages: 36

Brand: Oki Pages: 282

Brand: Oki Pages: 269

Brand: Oki Pages: 36

Brand: Oki Pages: 2

Brand: Oki Pages: 3

Brand: Oki Pages: 6

Brand: Oki Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands