Lexmark X925 7541-03 series Service Manual Download Page 170 | Manualshive

Page: 170 / 500

background image

3-32

Service Manual

7541-03x

Go Back

Previous

Next

Step 3: Develop

Once the laser exposes the photoconductor, the high-voltage power supply sends charge to the developer
roll (C). For each color, the toner cartridge engages the photoconductor so it is in contact with the surface.
Because of the charge difference between the toner on the developer roller and the electrostatic image created
by the laser, the toner will attract to the photoconductor only where the laser exposed the surface.

This process would be similar to using glue to write on a can and then rolling it over glitter. The glitter sticks to
the glue but won’t stick to the rest of the can.

Service tips

•

Never touch the surface of the developer roller with your bare hand. The oil from your skin may cause
a charge differential on the surface, and toner will not stick properly. The result would be repeating
blotches of voids/light print on a page. Then the affected cartridge will have to be replaced.

•

If the developer roller is damaged, it will not contact the surface of the photoconductor properly. The
result could be repeating marks, thin vertical voids, or thin vertical lines of color on the printed page.
Check the surface of the developer for damage.

C

«
...
168
169
170
171
172
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

WorkCentre 5325

Brand: Xerox Pages: 160

WorkCentre 5016

Brand: Xerox Pages: 2

WorkCentre 490cx

Brand: Xerox Pages: 258

WorkCentre 4260 Series

Brand: Xerox Pages: 210

WorkCentre 3550

Brand: Xerox Pages: 32

WorkCentre 3315DN

Brand: Xerox Pages: 191

WORKCENTER 5222

Brand: Xerox Pages: 28

VersaLink C71 Series

Brand: Xerox Pages: 247

VersaLink C7000

Brand: Xerox Pages: 2

Brand: Xerox Pages: 21

VersaLink B71 Series

Brand: Xerox Pages: 234

WorkCentre 6505

Brand: Xerox Pages: 4

WorkCentre 6015

Brand: Xerox Pages: 16

Brand: Xerox Pages: 4

Brand: Xerox Pages: 5

Brand: Xerox Pages: 8

WORKCENTRE 5735

Brand: Xerox Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands