Lexmark X925 7541-03 series Service Manual Download Page 86

Page: 86 / 500

2-48

Service Manual

7541-03x

Go Back

121.05 Fuser - fuser heater error

ON / OFF switch automatically switching to the Off position service check

Note:

If the machine turns off a few seconds after a POR, follow the procedure below. The automatic shut

down of the printer is a safety feature implemented to avoid fire, or damage to the printer. This is a feature
of the device.

126.xx Power switch error

Step

Action and questions

Yes

Is the fuser installed and seated properly?

Go to step 2.

Properly install
the fuser.

Are CN02 and CN04 on the LVPS, and CN16 on the
printhead control board properly connected?

Go to step 3.

Properly connect
all the cables.

Check the fuser connectors on the fuser power cable
for damage. Is there any damage?

Replace the fuser
power cable.

Go to step 4.

Check the fuser power cable for continuity. Is there
continuity?

Go to step 5

Replace the fuser
power cable

Replace the fuser. Does this fix the problem?

Problem solved

Go to step 6.

Replace the printhead controller board. Does this fix
the problem?

Problem solved

Go to step 7.

Replace the LVPS. See

“Low volt power supply

removal” on page 4-51

. Does this fix the problem?

Problem solved

Replace the fuser
power cable.

Step

Action and questions

Yes

POR the printer a couple times. Does the printer turn
off a few seconds after the POR?

Note:

When restarting the machine, you should see

the power switch physically move to the off position
when the machine turns off.

Go to step 2.

Problem resolved

Replace the fuser, power supply, and printhead
controller board. Does this fix the problem?

Problem
resolved.

Contact your
second level
support

Step

Action and questions

Yes

Is the power switch cable properly connected to CN27
on the engine controller board?

Properly connect
the connector.

Go to step 2

Replace the power switch. Does this fix the problem?

Problem resolved

Go to step 3.

Replace the engine controller board. Does this fix the
problem.

Problem resolved

Go to step 4.

Replace the power switch cable harness. Does this fix
the problem?

Problem resolved

Contact your
second level
support.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands

Lexmark X925 7541-03 series, Service Manual

Search results

Summary of Contents for X925 7541-03 series

Reviews:

Related manuals for X925 7541-03 series

Brands by name

Popular brands