Lexmark X925 7541-03 series Service Manual Download Page 163 | Manualshive

Page: 163 / 500

background image

Diagnostic aids

3-25

7541-03x

Go Back

Previous

Next

PAGE COUNTS

This menu lets you view the total page counts of the printer or the page counts broken down into color and mono
pages printed. Unlike in previous printers, none of these values can be changed.

Touch

Back

to return to the Diagnostics menu.

Serial Number

You can view the serial number.

Engine Setting

(1-16)

Warning:

The engine setting should not be changed without specific instructions from the next level of support.

Model Name

You can view the model name.

Configuration ID

The two configuration IDs are used to communicate information about certain areas of the printer that cannot be
determined using hardware sensors. The configuration IDs are originally set at the factory when the printer is
manufactured. However, you may need to reset Configuration ID 1 or Configuration ID 2 whenever you replace
the system board. The IDs consist of eight hexadecimal characters, including 0 through 9 and A through F.

Note:

When the printer detects a Configuration ID that is not defined or invalid, the following occurs:

•

The default standard model Configuration ID is used instead.

•

Configuration ID is the only function available in DIAGNOSTICS.

•

Unless the menu is in DIAGNOSTICS,

Check Config ID

appears.

To set the configuration ID:

1.

From the Diagnostics menu, navigate to:

Printer Setup

>

Configuration ID

2.

Enter the Configuration ID 1.

3.

Touch the Configuration ID 2 value to select it, and then enter the new Configuration ID

2.

4.

Touch

Submit

to save and validate the new IDs.

If either ID is invalid, then the printer discards the changes and returns to the original IDs.
If both IDs are valid, then the printer returns to the Diagnostics menu.

Cal Ref Adj

Warning:

This setting should not be changed without specific instructions from the next level of support.

«
...
161
162
163
164
165
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

PIXMA MG5600 Series

Brand: Canon Pages: 4

Brand: Lexmark Pages: 59

Brand: Olivetti Pages: 78

Brand: Konica Minolta Pages: 32

Brand: Oki Pages: 126

Brand: Ricoh Pages: 268

ECOSYS M6035cdn

Brand: Kyocera Pages: 31

Brand: Citizen Pages: 46

Ecosys FS-C5300DN

Brand: Kyocera Pages: 35

Brand: Tascam Pages: 2

Aficio SP 3300D

Brand: Ricoh Pages: 2

ScreenWriter Colour ScreenWriter

Brand: Xante Pages: 446

Brand: Ricoh Pages: 31

Adaptive CMYK+ Kit

Brand: Xerox Pages: 48

1-Port USB Print Server

Brand: IBM Pages: 15

Brand: Copystar Pages: 4

Brand: Oki Pages: 94

Brand: Oki Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands