Lexmark X925 7541-03 series Service Manual Download Page 151 | Manualshive

Page: 151 / 500

background image

Diagnostic aids

3-13

7541-03x

Go Back

Previous

Next

Energy Conserve

When Energy Conserve is on, the customer does not have access to disable the Sleep Mode function. When
Energy Conserve is off, Disable appears as an additional menu item in the Sleep Mode menu. This setting only
affects the values that are displayed in the Sleep Mode menu.

Fax Low Power Support

This menu has the following settings:

Auto

—The printer checks the Caller ID Pattern setting to determine if the fax chip should enter low power

mode.

Permit Sleep

—The fax chip enters low power mode when needed, regardless of the Caller ID Patter

setting.

Disable Sleep

—The fax chip never enters low power mode.

Min Copy Memory

This menu lets you select the amount of memory dedicated to storing copy jobs. The values may be 25 MB, 35
MB, 50 MB, 80 MB, and 100 MB. The default is 80 MB. Values will be displayed only if the amount of installed
DRAM is at least twice the amount of the value. For example, at least 200 MB of installed DRAM is required to
display the 100 MB selection.

NumPad Job Assist

When this setting is set to On, a user can initiate scanner-related jobs, and enter values for a limited number of
settings related to those jobs, using the keypad.

Touch

Back

to exit without changing the setting.

Format Fax Storage

This setting enables you to format the non-volatile storage used for storing faxes.

Note:

If an advanced password has been established, you must enter this password in order to change the

setting.

Fax Storage Location

This menu allows you to select either NAND or the printer hard disk (Disk) as the fax storage location. If the
printer hard disk is removed, then this menu no longer appears.

Auto Align Adj

The printer automatically runs a Toner Patch Sensing (TPS) diagnostic after certain key events. Depending on
the type of event, the results of the diagnostics can trigger either a color adjust calibration or an alignment
calibration. If necessary, the printer will automatically adjust the alignment.

If Auto Align Adj is set to Off, then the diagnostic still runs, but the printer will not use the resulting data to
automatically adjust alignment. This could eventually lead to the user having to adjust alignment manually.
Therefore, Auto Align Adj should not be set to Off during normal printer usage.

«
...
149
150
151
152
153
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: NCR Pages: 5

Brand: Olympus Pages: 2

Brand: Zmorph Pages: 16

Brand: Kyocera Pages: 157

Delta Rostock mini G2 pro

Brand: Geeetech Pages: 89

Brand: Olivetti Pages: 139

Brand: Lexmark Pages: 2

Brand: AGFA Pages: 266

Brand: Riso Pages: 208

Brand: Lexmark Pages: 289

Brand: Astro Machine Pages: 5

Brand: Ricoh Pages: 173

Brand: InfoPrint Pages: 170

Brand: Wasp Pages: 82

ColourLaser 21 Series

Brand: Xante Pages: 32

Brand: Kyocera Pages: 72

Brand: Epson Pages: 157

Brand: WOOSIM Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands