manualshive.com logo in svg

Lexmark X925 7541-03 series, Service Manual

The Lexmark X925 7541-03 series is a high-performance printer designed to meet all your business needs. With our Service Manual, you can easily troubleshoot any issues and perform maintenance tasks hassle-free. Download this invaluable manual for free at manualshive.com and ensure the optimal performance of your Lexmark printer.

Share
Download
background image

2-82

  Service Manual

7541-03x

Go Back

Previous

Next

Fax symptoms

Faxes fail to transmit

Note:  

Before performing this service check, verify that the correct country code for the MFP is selected. This 

setting must match the country in which the MFP is used to transmit and receive faxes. If the setting is wrong, 
the modem settings can be changed in the Fax/SE menu. See step 14. These settings should only be changed 
with guidance from your second-level support.

Step

Questions / actions

Yes

No

1

Is the phone line properly connected to the 
modem card and the wall jack?

Go to step 3.

Go to step 2.

2

Properly connect the phone line to the 
modem card and wall jack.

Did this fix the problem?

Problem resolved

Go to step 3.

3

Test the phone line’s ability to send and 
receive calls.

Did the phone line work properly?

Go to step 5.

Go to step 4.

4

Use the MFP on a properly functioning 
phone jack.

Did this fix the problem?

Problem resolved.

Go to step 5.

5

Is the phone line being used by the MFP an 
analog line?

Go to step 8.

Go to step 6.

6

Is the line being used a VOIP line?

Go to step 7.

Go to step 8.

7

Have the system administrator verify that 
the VOIP server is configured to receive 
faxes.

Is the server properly configured?

Go to step 8.

Stop here. The issue is 
VOIP related. The 
VOIP provider needs to 
change the server 
configuration.

8

Is the MFP on a PABX?

Go to step 9.

Go to step 10.

9

Enable 

Behind a PABX

 under fax settings 

in the Administration menu.

Did this fix the issue?

Problem fixed.

Disable 

Behind a 

PABX,

 and go to 

step10.

10

Is a dial prefix needed to get an outside 
line?

Go to step 11.

Go to step 12.

11

Try sending a fax using a dial prefix.

Did the fax transmit?

Problem fixed.

Go to step 12.

12

Is the fax failing to send to one specific 
destination?

Go to step 13.

Go to step 14.

13

Check the device that cannot receive a fax. 
Can it send a fax?

Go to step 14.

Stop here. The issue is 
with the other device.

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Xerox ColorQube 8580 System Administrator Manual preview
ColorQube 8580
Brand: Xerox Pages: 93
Xerox C235 Safety, Regulatory, Recycling, And Disposal Reference Manual preview
C235
Brand: Xerox Pages: 36
Xerox Copycentre C118 Evaluator Manual preview
Copycentre C118
Brand: Xerox Pages: 12
Xerox 7400DN - Phaser Color LED Printer Accessories Manual preview
7400DN - Phaser Color LED Printer
Brand: Xerox Pages: 3
Xerox 4890 Advanced Product Reference preview
4890 Advanced
Brand: Xerox Pages: 136
Xerox 4250 - WorkCentre - Copier Secure Installation And Operation preview
4250 - WorkCentre - Copier
Brand: Xerox Pages: 4
Xerox 4250 - WorkCentre - Copier Brochure & Specs preview
4250 - WorkCentre - Copier
Brand: Xerox Pages: 4
Xerox ColorQube 9201 Quick Manual preview
ColorQube 9201
Brand: Xerox Pages: 8
Xerox 4150 - WorkCentre B/W Laser Secure Installation And Operation preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 4
Xerox 4150 - WorkCentre B/W Laser Installation Instructions Manual preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 40
Xerox 4150 - WorkCentre B/W Laser Getting Started Manual preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 38
Xerox 4150 - WorkCentre B/W Laser User Manual preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 201
Xerox 4150 - WorkCentre B/W Laser Evaluator Manual preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 24
Xerox 4118P - WorkCentre B/W Laser Quick Start Manual preview
4118P - WorkCentre B/W Laser
Brand: Xerox Pages: 2
Xerox 3635MFP - Phaser B/W Laser System Administration Manual preview
3635MFP - Phaser B/W Laser
Brand: Xerox Pages: 212
Xerox 3300MFP - Phaser B/W Laser Specifications preview
3300MFP - Phaser B/W Laser
Brand: Xerox Pages: 4
Xerox 6279 User Manual preview
6279
Brand: Xerox Pages: 216
Xerox 3250D - Phaser B/W Laser Printer Configuration Manual preview
3250D - Phaser B/W Laser Printer
Brand: Xerox Pages: 6

Brands by name

Popular brands

Load more brands