Lexmark X925 7541-03 series Service Manual Download Page 128 | Manualshive

Page: 128 / 500

background image

2-90

Service Manual

7541-03x

Go Back

Previous

Next

Option card service check

USB port service check

1.

Perform a print test to make sure the printer prints correctly. Verify that the indicator light is on, then print
the menu settings by

Menu Settings Page

from the

Reports Menu

in the menus.

2.

Be sure the printer USB cable is designed for bidirectional printing.

3.

Be sure the user’s application is set up correctly.

4.

If the internal print test page prints correctly, the user’s application/printer driver is set up correctly, and the
USB cable is installed, but the printer still fails to print on command from the host computer, then replace
the controller board.

5.

Check the USB cable for continuity.

False close door service check

Option card service check

FRU

Action

Option cards

Controller board

Option card connection
cable

Warning:

Do not

replace the engine
board and controller
board at the same
time. Each board
contains the printer
settings. When either
of these boards is new,
it obtains the settings
from the other board.
Settings are lost when
both are new and
replaced at the same
time.

Card

Remove all the option cards from the device.

Install each card individually. Restart the MFP after each card is installed.

Remove the card and repeat the previous step with a different card till all cards are
checked.

When a faulty card is found, replace the card. If the error persists after replacing the option
card, replace the RIP board. See

“RIP board removal” on page 4-73

.

If there are no errors found testing the cards individually, install the cards on at a time.
Restart the MFP after each card is installed.

Cables

If the cards do not trigger an error, check the option card connection cables for continuity.

Step

Action and questions

Yes

No

1

Open and close the right cover. Does the message
reset?

Problem solved

Go to step 2.

2

Check the right door release lever. Does it operate
smoothly, and is the interlock actuator intact?

Go to step 3.

Replace the
faulty part on the
door.

3

Is the interlock switch cable properly connected to the
interlock switch and CN23 on the engine board?

Go to step 4.

Properly connect
the interlock
switch cable.

4

Replace the interlock switch. Did this fix the problem?

Problem solved.

Go to step 5.

5

Replace the engine board. Did this fix the problem?

Problem solved.

Contact your
second level
support.

«
...
126
127
128
129
130
...
»

Summary of Contents for X925 7541-03 series





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X925 7541-03 series

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: TallyGenicom Pages: 166

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

Brand: Afinia 3D Pages: 47

Brand: Inno3D Pages: 23

Brand: Ricoh Pages: 2

LaserPro StellarMark IFII Series

Brand: GCC Technologies Pages: 111

Brand: ColorGATE Pages: 6

Brand: Pantum Pages: 164

Brand: Creality Pages: 24

Blaster ADVANTAGE

Brand: CognitiveTPG Pages: 20

Brand: Konica Minolta Pages: 165

PIXMA E300 series

Brand: Canon Pages: 28

Brand: Canon Pages: 115

Brand: Canon Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands