Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 40

Page: 40 / 264

The following illustration shows the components of server models with up to eight 2.5-inch hot-swap SAS
hard disk drives.

Figure 12. Components of server models with up to eight 2.5-inch hot-swap SAS hard disk drives

Intelligent Diagnostics Module (available in some

models)

Hard-disk-drive bay 0

Front panel

Front system fan 1

Optical drive bay 2 (with an optical drive installed

in some models)

System board battery

Optical drive bay 1 (with an optical drive installed)

Low-profile PCI card bracket

Hard-disk-drive bay 7

Main PCI card bracket

Hard-disk-drive bay 6

Expansion card

Hard-disk-drive bay 5

Heat sink and fan assembly

Hard-disk-drive bay 4

System board

Hard-disk-drive bay 3

Rear system fan

Hard-disk-drive bay 2

Power supply

Hard-disk-drive bay 1

Four memory slots (installed memory modules vary by

model)

• For more information about

, see “Front view of the server” on page 15.

Note:

The Intelligent Diagnostics Module

is only available in some models and the IDM panel also

varies by model. See “Intelligent Diagnostics Module” on page 18.

ThinkServer TS430 Hardware Maintenance Manual

Summary of Contents for ThinkServer TS430









































































































































































































































































Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands

Lenovo ThinkServer TS430, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands