Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 42

Page: 42 / 264

The following illustration shows the components of server models with up to four 3.5-inch hot-swap hard
disk drives.

Figure 13. Components of server models with up to four 3.5-inch hot-swap hard disk drives

Intelligent Diagnostics Module (available in some

models)

Front system fan 1

Front panel

System board battery

Optical drive bay 2 (with an optical drive installed

in some models)

Expansion card (varies by model)

Optical drive bay 1 (with an optical drive installed)

Heat sink and fan assembly

Hard-disk-drive bay 3

System board

Hard-disk-drive bay 2

Rear system fan

Hard-disk-drive bay 1

Power supply

Hard-disk-drive bay 0

Four memory slots (installed memory modules vary by

model)

• For more information about

, see “Front view of the server” on page 15.

Note:

The Intelligent Diagnostics Module

is only available in some models and the IDM panel also

varies by model. See “Intelligent Diagnostics Module” on page 18.

• There is a 3.5-inch hot-swap hard disk drive or a dummy hard-disk-drive tray installed in each

hard-disk-drive bay (

Note:

The number of the installed hard disk drives varies by model. For the vacant drive bay, there is a

dummy hard-disk-drive tray to cover the place.

ThinkServer TS430 Hardware Maintenance Manual

Summary of Contents for ThinkServer TS430









































































































































































































































































Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands

Lenovo ThinkServer TS430, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands