Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 190

Page: 190 / 264

4. Position the server cover on the chassis so that the rail on the bottom of the server cover engages the

bottom rail on the chassis. Then, align the four tabs

on the server cover with the corresponding holes

in the top edge of the chassis. Pivot the server cover to close it.

Figure 113. Closing the server cover

5. Slide the server cover to the front of the chassis until it snaps into position.

Figure 114. Installing the server cover

6. Tighten the thumbscrew on the server cover to secure the server cover in place.

178

ThinkServer TS430 Hardware Maintenance Manual

Summary of Contents for ThinkServer TS430









































































































































































































































































Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands

Lenovo ThinkServer TS430, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer TS430

Reviews:

Related manuals for ThinkServer TS430

Brands by name

Popular brands